THE-200 Duct / Wall-Mount Humidity & Temperature Sensor | iCoolheat

THE-200 Duct / Wall-Mount Humidity & Temperature Sensor | iCoolheat 1
  • THE-200 Duct / Wall-Mount Humidity & Temperature Sensor | iCoolheat 1
  • Place of Origin:China
  • Brand Name:iCoolheat
  • MOQ:5 pcs
  • Packaging Details:Standard Export Carton
  • Payment Terms:T/T
  • Supply Ability:20,000 pcs/month
  • Lead Time:7 days for standard models

THE-200 duct or wall-mount humidity and temperature sensor and transmitter, with 0–100 %RH measurement and analogue or Modbus RTU output options. Select the installation method and signal combination to match the HVAC or building automation application. Passive temperature sensing is available as a version option.

Key features

  • Duct or wall-mount humidity and temperature measurement.

  • Humidity range: 0–100 %RH.

  • Catalogue temperature range: −40 to +140 °C (−40 to +284 °F).

  • Conformal coating for sensing-element protection.

  • 0–10 V, 0–5 V, 4–20 mA, passive temperature and Modbus RTU options.

  • Housing IP65 / probe IP30.

Technical specifications

ParameterTHE-200
Product typeDuct / Wall-Mount Humidity & Temperature Sensor & Transmitter
Humidity measuring range0–100 %RH
Temperature measuring range−40 to +140 °C (−40 to +284 °F)
Sensing-element protectionConformal coating
Output options0–10 V / 0–5 V / 4–20 mA / passive temperature sensor
Digital interface optionModbus RTU
Mounting optionsWall mount / duct mount
Protection ratingHousing IP65 / Probe IP30

The signals are version options, not simultaneous outputs from every unit. The passive option applies to temperature sensing. Confirm the configured measuring range, signal combination and mounting arrangement when ordering.

Applications

The THE-200 humidity and temperature transmitter supports HVAC air monitoring and building automation applications using wall or duct mounting. Select a location representative of the air being measured and match the signal to the controller input. The housing and probe have different protection ratings, which must be considered separately.

Output selection

Choose 0–10 V or 0–5 V to match a voltage input, or 4–20 mA for a compatible current input. The English manual identifies three-wire current output as standard, with a two-wire version requiring customization. Confirm the supplied configuration before connection.

For a passive temperature input, the manual lists NTC 10 kΩ, NTC 20 kΩ, Pt100 and Pt1000 options. For digital communication, it lists RS-485 / Modbus RTU. Confirm the exact sensing element or communication configuration needed by the BMS, DDC or PLC.

Selection questions

Should I choose wall or duct mounting?

Choose according to where the air condition must be measured and the available mounting arrangement. The catalogue lists both formats for THE-200. Specify the intended installation so the suitable supplied configuration can be confirmed.

How is THE-200 different from THE-100?

THE-100 is listed for duct mounting; THE-200 lists wall or duct mounting. Select using the mounting requirement and probe arrangement, and confirm the signal version separately rather than assuming similar housings mean identical installation details.

What accuracy is available?

The THE-200 English manual lists ±3 %RH humidity accuracy and ±0.3 °C temperature accuracy. Confirm the applicable conditions, operating point and selected version for your required tolerance. Do not assume these figures apply uniformly over the entire catalogue range.

Does the temperature range determine the analogue scaling?

No. The catalogue lists −40 to +140 °C, but the configured analogue range must be specified for the ordered version and matched to the controller. The manual uses separate range selections; do not assume every unit uses the full catalogue span.

Does IP65 apply to the exposed humidity probe?

The catalogue specifies housing IP65 and probe IP30. Conformal coating and a 0–100 %RH measuring range do not establish that the probe is waterproof or suitable for immersion or condensation. Check the environment for the actual installation.

Is every 4–20 mA version two-wire?

No. The English manual states three-wire as standard and two-wire by customization. Specify the required arrangement and confirm the power and connection requirements for the supplied version.

Request a quotation

MOQ: 5 pcs. Email info@heatcoolsmart.com with the mounting method, expected humidity and temperature conditions, required output combination, controller input and quantity.

For the duct-only model, see THE-100 duct humidity and temperature sensor and transmitter.

Request Free Quote

Other Products You May Like

QUALITY · RELIABILITY · INNOVATION
Get In Touch With Us
Follow Us
Top